Toyota Corolla Cross Owners & Service Manuals

Toyota Corolla Cross: Customize Parameters

CUSTOMIZE PARAMETERS

CUSTOMIZE BLIND SPOT MONITOR SYSTEM

(a) Customizing with the GTS

NOTICE:

  • When the customer requests a change in a function, first make sure that the function can be customized.
  • Be sure to make a note of the current settings before customizing.
  • When troubleshooting a function, first make sure that the function is set to the default setting.

(1) Turn the ignition switch to ON.

(2) Turn the blind spot monitor system on.

(3) Enter the following menus: Body Electrical / Blind Spot Monitor "B" or Blind Spot Monitor "A" / Utility

(4) Select the setting by referring to the table below.

Blind Spot Monitor

Tester Display

Description

Default

Setting

ECU

BSM Function

Switches the BSM function on and off.

Valid

$00:Valid,$01:Invalid

Blind Spot Monitor Sensor LH (B)

RCTA Function

Switches the RCTA function on and off.

Valid

$00:Valid,$01:Invalid

Blind Spot Monitor Sensor LH (B)

SEA Function

Switches the safe exit assist system on and off.

Effectively

$00:Valid,$01:Invalid

Blind Spot Monitor Sensor LH (B)

SEA Detection Sensitivity

Sets the sensitivity of the notification of the safe exit assist system.

Middle

$01:Low,$02:Middle,$03:High

Blind Spot Monitor Sensor LH (B)

RCTA Buzzer Volume Setting

Sets the volume of the RCTA (meter buzzer).

Medium

$01:Small,$03:Medium,$05:Large

Blind Spot Monitor Sensor LH (B)

(b) Customizing with the multi-information display

NOTICE:

  • When the customer requests a change in a function, first make sure that the function can be customized.
  • Be sure to make a note of the current settings before customizing.
  • When troubleshooting a function, first make sure that the function is set to the default setting.
BSM

Display

Description

Default

Setting

ECU

BSM

Switches the BSM function on and off.

ON

ON/OFF

Blind Spot Monitor Sensor LH (B)

Support timing

Sets the notification timing for vehicles approaching from behind the vehicle.

Middle

Early/Middle/Late

Blind Spot Monitor Sensor LH (B)

Brightness

Sets the brightness of the indicators in the outer rear view mirror assemblies.

Bright

Dim/Bright

Blind Spot Monitor Sensor LH (B)

RCTA

Display

Measurement Item

Default

Setting

ECU

RCTA

Switches the RCTA function on and off.

ON

ON/OFF

Blind Spot Monitor Sensor LH (B)

Volume

Adjusts the volume for the RCTA buzzer (meter buzzer).

Medium

Small/Medium/Large

Blind Spot Monitor Sensor LH (B)

SEA (Safe Exit Assist)

Display

Measurement Item

Default

Setting

ECU

Safe Exit Assist

Turns the safe exit assist system ON/OFF.

ON

ON/OFF

Blind Spot Monitor Sensor LH (B)

Sensitivity

Sets the sensitivity of the notification of the safe exit assist system.

Medium

Small/Medium/Large

Blind Spot Monitor Sensor LH (B)

Mirror indicate

Switches the outer rear view mirror indicator on and off.

ON

ON/OFF

Blind Spot Monitor Sensor LH (B)

    READ NEXT:

     Problem Symptoms Table

    PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed i

     Terminals Of Ecu

    TERMINALS OF ECU BLIND SPOT MONITOR SENSOR LH (B) Terminal No. (Symbol) Terminal Description Condition Specified Condition S12-4 (OM

     Diagnosis System

    DIAGNOSIS SYSTEM DESCRIPTION (a) Blind spot monitor data and Diagnostic Trouble Codes (DTCs) can be read from the Data Link Connector 3 (DLC3) of the vehicle. When the system seems to be malfunc

    SEE MORE:

     Electronic Brake Booster Control Module "A" Backup Power Supply Voltage System Voltage Low (C125DA2,C125DA3)

    DESCRIPTION The brake control power supply assembly is used as an auxiliary power supply for brake control when the voltage of the auxiliary battery is low. DTC No. Detection Item DTC Detection Condition Trouble Area MIL DTC Outpu

     Output Speed Sensor Circuit Short to Battery (P072012,P072014,P072031)

    DESCRIPTION The transmission revolution sensor (NOUT) detects the output shaft speed and sends it to the TCM. The TCM determines if belt mode has been entered by comparing the transmission revolution sensor (NOUT) and (NSS) signals. DTC No. Detection Item DTC

    © 2020-2025 Copyright www.tcorollacross.com PT NL