Toyota Corolla Cross: Ultrasonic Sensor (Front Right Center) Component Internal Failure (C1AE396)
DESCRIPTION
The front center ultrasonic sensor (FRC sensor) is installed on the front bumper. The clearance warning ECU assembly detects obstacles based on signals it receives from the front center ultrasonic sensor (FRC sensor). If an open circuit or other malfunction occurs in the front center ultrasonic sensor (FRC sensor), the front center ultrasonic sensor (FRC sensor) does not operate correctly.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
C1AE396 |
Ultrasonic Sensor (Front Right Center) Component Internal Failure |
Front center ultrasonic sensor (FRC sensor) failure |
|
CAUTION / NOTICE / HINT
NOTICE:
- Perform registration after replacing or removing and installing the
ultrasonic sensor or clearance warning ECU assembly.
Click here
.gif)
- If a DTC is detected again after the repair, turn the ignition switch to ON and turn the intuitive parking assist system on, and then clear the DTC.
PROCEDURE
|
1. |
CLEAR DTC |
(a) Clear the DTCs.
Body Electrical > Clearance Warning > Clear DTCs
|
.gif)
|
2. |
CHECK FOR DTC |
(a) Check for DTCs.
Body Electrical > Clearance Warning > Trouble Codes|
Result |
Proceed to |
|---|---|
|
DTCs are not output |
A |
|
C1AE396 and C1AE387 are output |
B |
|
C1AE396 is output |
C |
|
None of the above conditions are met |
D |
| A | .gif)
|
USE SIMULATION METHOD TO CHECK |
| B |
|
GO TO DTC (C1AE387) |
| D |
|
GO TO DTC CHART
|
|
|
3. |
REPLACE FRONT CENTER ULTRASONIC SENSOR (FRC SENSOR) |
(a) Replace the front center ultrasonic sensor (FRC sensor) with a known good one.
HINT:
- Click here
- All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.
|
|
4. |
CLEAR DTC |
(a) Clear the DTCs.
Body Electrical > Clearance Warning > Clear DTCs
|
|
5. |
CHECK FOR DTC |
(a) Check for DTCs.
Body Electrical > Clearance Warning > Trouble Codes|
Result |
Proceed to |
|---|---|
|
DTCs are not output |
A |
|
C1AE396 is output |
B |
|
None of the above conditions are met |
C |
| A |
|
END (FRONT CENTER ULTRASONIC SENSOR [FRC SENSOR] WAS DEFECTIVE) |
| B |
|
REPLACE CLEARANCE WARNING ECU ASSEMBLY
|
| C |
|
GO TO DTC CHART
|
READ NEXT:
Ultrasonic Sensor (Front Right Corner) Missing Message (C1AE487)
DESCRIPTION
This DTC is output when an open circuit or short occurs in the
communication line between a front corner ultrasonic sensor (FR sensor) and the
front center ultrasonic sensor (FRC sens
Ultrasonic Sensor (Front Right Corner) Component Internal Failure (C1AE496)
DESCRIPTION
The front corner ultrasonic sensor (FR sensor) is installed
on the front bumper. The clearance warning ECU assembly detects obstacles based
on signals it receives from the front corne
Ultrasonic Sensor (Rear Left Corner) Missing Message (C1AE687)
DESCRIPTION
This DTC is output when an open circuit or short occurs in the
communication line between a rear corner ultrasonic sensor (RL sensor) and the clearance
warning ECU assembly, or when a
SEE MORE:
Cylinder 1 Injector Circuit Range/Performance (P02EE00,P02EF00,P02F000,P02F100)
DESCRIPTION By using Partial Lift Fuel Injection Control to spray fuel before the needle inside each direct fuel injector assembly has fully opened, the injection of fuel by the direct fuel injector assembly can be precisely controlled at partial lift. Due to the influence on the injected fuel volum
Stop And Start System Cancel Switch Assembly
InspectionINSPECTION PROCEDURE
1. INSPECT ECO RUN CANCEL SWITCH ASSEMBLY (COMBINATION SWITCH ASSEMBLY)
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection Switch Condition
Specified Condition
I61-8 (ERC)
