Toyota Corolla Cross Owners & Service Manuals

Toyota Corolla Cross: Right Rear Wheel ABS Hold Solenoid Control Circuit Short to Battery (C12E712,...,C12F249)

Toyota Corolla Cross (2022-2026) Service Manual / Brake / Brake Control / Dynamic Control Systems / Electronically Controlled Brake System (for Gasoline Model) / Right Rear Wheel ABS Hold Solenoid Control Circuit Short to Battery (C12E712,...,C12F249)

DESCRIPTION

The ABS solenoid relay and solenoid valves are built into the brake actuator assembly.

The rear solenoid valve RH controls the brake fluid pressure of the rear wheel cylinder RH of the vehicle.

When this DTC is stored, the fail-safe function operates and the ABS solenoid relay is turned off to prevent the solenoid valves from operating.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C12E712

Right Rear Wheel ABS Hold Solenoid Control Circuit Short to Battery

A short to +B in the solenoid circuit is detected during the self test.

Skid control ECU (brake actuator assembly)

C12E714

Right Rear Wheel ABS Hold Solenoid Control Circuit Short to Ground or Open

An open or short in the solenoid circuit is detected during the self test.

Skid control ECU (brake actuator assembly)

C12E71C

Right Rear Wheel ABS Hold Solenoid Control Circuit Voltage Out of Range

  • A current leak in the solenoid circuit is detected during the self test.
  • The solenoid operation request signal and solenoid operation feedback signal do not match for a certain period of time.

Skid control ECU (brake actuator assembly)

C12E71E

Right Rear Wheel ABS Hold Solenoid Control Circuit Resistance Out of Range

An abnormal resistance in the solenoid circuit is detected during the self test.

Skid control ECU (brake actuator assembly)

C12E749

Right Rear Wheel ABS Hold Solenoid Control Internal Electronic Failure

An internal malfunction in the solenoid circuit is detected during the self test.

Skid control ECU (brake actuator assembly)

C12F212

Right Rear Wheel ABS Release Solenoid Control Circuit Short to Battery

A short to +B in the solenoid circuit is detected during the self test.

Skid control ECU (brake actuator assembly)

C12F214

Right Rear Wheel ABS Release Solenoid Control Circuit Short to Ground or Open

An open or short in the solenoid circuit is detected during the self test.

Skid control ECU (brake actuator assembly)

C12F21C

Right Rear Wheel ABS Release Solenoid Control Circuit Voltage Out of Range

  • A current leak in the solenoid circuit is detected during the self test.
  • The solenoid operation request signal and solenoid operation feedback signal do not match for a certain period of time.

Skid control ECU (brake actuator assembly)

C12F21E

Right Rear Wheel ABS Release Solenoid Control Circuit Resistance Out of Range

An abnormal resistance in the solenoid circuit is detected during the self test.

Skid control ECU (brake actuator assembly)

C12F249

Right Rear Wheel ABS Release Solenoid Control Internal Electronic Failure

An internal malfunction in the solenoid circuit is detected during the self test.

Skid control ECU (brake actuator assembly)

PROCEDURE

1.

REPLACE BRAKE ACTUATOR ASSEMBLY

Click here

NEXT

END

    READ NEXT:

     Brake System Control Module "A" System Voltage System Voltage High (C137BA3)

    DESCRIPTION If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits ABS operation. This DTC

     Stop Lamp Relay Actuator Stuck On (C13807E)

    DESCRIPTION When any of the following conditions are met, the skid control ECU (brake actuator assembly) sets the drive output (STPO) ON which operates the stop light control relay (stop light sw

     Stop Lamp Relay Actuator Stuck Off (C13807F)

    DESCRIPTION Refer to DTC C13807E. Click here DTC No. Detection Item DTC Detection Condition Trouble Area C13807F Stop Lamp

    SEE MORE:

     Disposal

    DISPOSAL PROCEDURE 1. DISPOSE OF REAR SHOCK ABSORBER ASSEMBLY (a) Extend the piston rod and secure the rear shock absorber assembly at an angle in a vise. (b) Using a hacksaw, slowly make a hole at the position indicated by the arrow

     Problem Symptoms Table

    PROBLEM SYMPTOMS TABLE NOTICE: When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may

    © 2020-2026 Copyright www.tcorollacross.com PT NL