Toyota Corolla Cross Owners & Service Manuals

Toyota Corolla Cross: Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message (U015587)

Toyota Corolla Cross (2022-2024) Service Manual / Engine & Hybrid System / M20a-fks (engine Control) / Sfi System / Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message (U015587)

DESCRIPTION

The ECM and combination meter assembly send and receive signals via CAN communication.

If a communication error occurs between the ECM and combination meter assembly, the ECM illuminates the MIL and stores this DTC.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Note

U015587

Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message

All of the following conditions are met for 2.6 seconds or more (1 trip detection logic).

  • Ignition switch ON
  • Auxiliary battery voltage is 10 V or higher
  • No communication between ECM and combination meter assembly
  • CAN communication system
  • Combination meter assembly
  • ECM

Comes on

  • SAE Code: U0155
  • DTC for Mexico Models: Does not apply

MONITOR STRATEGY

Related DTCs

U0155: Lost communication with instrument panel cluster control module (verify communication)

Required Sensors/Components (Main)

ECM

Required Sensors/Components (Related)

-

Frequency of Operation

Continuous

Duration

2.6 seconds

MIL Operation

Immediate

Sequence of Operation

None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever the following DTCs are not stored

None

Auxiliary battery voltage

10 V or higher

Ignition switch

ON

TYPICAL MALFUNCTION THRESHOLDS

Communication signal

Lost communication with instrument panel cluster control module

CONFIRMATION DRIVING PATTERN

HINT:

  • After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

    Click here

  • When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.

    Click here

  1. Connect the GTS to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the GTS on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the ignition switch off and wait for at least 30 seconds.
  6. Turn the ignition switch to ON.
  7. Turn the GTS on.
  8. Wait 5 seconds or more [A].
  9. Enter the following menus: Powertrain / Engine / Trouble Codes [B].
  10. Read the DTCs.

    HINT:

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  11. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  12. Input the DTC: U015587.
  13. Check the DTC judgment result.

    GTS Display

    Description

    NORMAL

    • DTC judgment completed
    • System normal

    ABNORMAL

    • DTC judgment completed
    • System abnormal

    INCOMPLETE

    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    HINT:

    • If the judgment result is NORMAL, the system is normal.
    • If the judgment result is ABNORMAL, the system has a malfunction.
    • If the judgment result is INCOMPLETE, perform steps [A] through [B] again.
    • [A] to [B]: Normal judgment procedure.

      The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

    • When clearing the permanent DTCs, do not disconnect the cable from the auxiliary battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.

GO TO CAN COMMUNICATION SYSTEM

(a) Refer to the CAN Communication System.

Click here

NEXT

END

    READ NEXT:

     Lost Communication with Stop and Start Control Module Missing Message (U110387)

    DESCRIPTION The ECM and engine stop and start ECU send and receive signals via CAN communication. If a communication error occurs between the ECM and engine stop and start ECU, the ECM stores this D

     Lost Communication with ECM/PCM "A" (ch5) Missing Message (U115C87)

    DESCRIPTION The ECM and skid control ECU (brake actuator assembly) send and receive signals via CAN communication. If a communication error occurs between the ECM and skid control ECU (brake actuato

     ECM Power Source Circuit

    DESCRIPTION When the ignition switch is turned to ON, the auxiliary battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes current to fl

    SEE MORE:

     Utility

    UTILITY REFRIGERANT SHORTAGE CHECK USING GTS (a) Check that the following conditions are met and perform the refrigerant shortage check according to the display on the GTS. Measurement Condition: Item Condition A/C switch On Ambient temperature*1 0 to 49°C (32 to 120

     Additional Key cannot be Registered

    DESCRIPTION If additional registration is not possible, a malfunction of the electrical key transmitter sub-assembly, certification ECU (smart key ECU assembly), engine switch, No. 1 indoor electrical key antenna assembly (front floor) or door control receiver is suspected. CAUTION / NOTICE / HINT

    © 2020-2024 Copyright www.tcorollacross.com