Toyota Corolla Cross Owners & Service Manuals

Toyota Corolla Cross: Internal Control Module EEPROM Data Memory Failure (P062F44)

Toyota Corolla Cross (2022-2025) Service Manual / Engine & Hybrid System / M20a-fxs (engine Control) / Sfi System / Internal Control Module EEPROM Data Memory Failure (P062F44)

DESCRIPTION

The ECM monitors its internal operation and stores this DTC when it detects an internal malfunction.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Note

P062F44

Internal Control Module EEPROM Data Memory Failure

An ECM internal error (EEPROM) (1 trip detection logic).

ECM

Comes on
  • SAE Code: P062F
  • DTC for Mexico Models: Applies

MONITOR DESCRIPTION

The ECM monitors its internal operation. If the internal operation is malfunctioning, the ECM illuminates the MIL and stores this DTC.

MONITOR STRATEGY

Related DTCs

P062F: Internal control module EEPROM error functional

Required Sensors/Components (Main)

ECM

Required Sensors/Components (Related)

-

Frequency of Operation

Continuous: Case 1, Case 2

Once per driving cycle: Case 3

Duration

-

MIL Operation

Immediate

Sequence of Operation

None

TYPICAL ENABLING CONDITIONS

All

Monitor runs whenever the following DTCs are not stored

None
Case 1

All of the following conditions are met

-

Permanent fault code

Not stored

OBDII system commands

Store

Auxiliary battery voltage

8 V or higher
Case 2

All of the following conditions are met

-

Permanent fault code

Stored

OBDII system commands

Clear

Auxiliary battery voltage

8 V or higher
Case 3

Auxiliary battery voltage

8 V or higher

TYPICAL MALFUNCTION THRESHOLDS

Case 1

The following condition is met

2 data or more

One of the following conditions (a), (b) or (c) is met

More than 3 times

(a) EEPROM access error

Occurred

(b) Permanent fault code

Not stored

(c) Permanent fault code

Not equal to commanded fault code
Case 2

The following condition is met

2 data or more

Either of the following conditions (a) or (b) is met

More than 3 times

(a) EEPROM access error

Occurred

(b) Permanent fault code

Stored
Case 3

Either of the following conditions is met

1 or 2

1. The following condition is met

2 data or more

EEPROM access error (more than 3 times)

Occurred

2. Permanent fault code data (more than 10 times)

Mismatch

CONFIRMATION DRIVING PATTERN

HINT:

  • After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

    Click here

  • When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.

    Click here

  1. Connect the GTS to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the GTS on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the GTS off.
  6. Turn the ignition switch off.
  7. Disconnect the GTS.
  8. Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 1 minute.
  9. Connect the cable to the negative (-) auxiliary battery terminal.
  10. Connect the GTS to the DLC3.
  11. Start the engine and wait 30 seconds or more [A].
  12. Turn the GTS on.
  13. Enter the following menus: Powertrain / Engine / Trouble Codes [B].
  14. Read the pending DTCs.

    HINT:

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  15. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  16. Input the DTC: P062F44.
  17. Check the DTC judgment result.

    GTS Display

    Description

    NORMAL
    • DTC judgment completed
    • System normal

    ABNORMAL
    • DTC judgment completed
    • System abnormal

    INCOMPLETE
    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    HINT:

    • If the judgment result is NORMAL, the system is normal.
    • If the judgment result is ABNORMAL, the system is malfunctioning.
    • [A] to [B]: Normal judgment procedure.

      The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

    • When clearing the permanent DTCs, do not disconnect the cable from the auxiliary battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.

CAUTION / NOTICE / HINT

NOTICE:

  • After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  • Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the Freeze Frame Data and Vehicle Control History can be useful for troubleshooting.

    Click here

    (Select Powertrain in Health Check and then check the time stamp data.)

    Click here

  • If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

    Click here

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.

CLEAR DTC

(a) Clear the DTCs.

Powertrain > Engine > Clear DTCs

(b) Turn the ignition switch off.

NEXT

2.

READ OUTPUT DTC (DTC P062F44)

(a) Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 1 minute.

(b) Connect the cable to the negative (-) auxiliary battery terminal.

(c) Start the engine and wait 30 seconds or more.

(d) Enter the following menus.

(e) Read the DTCs.

Powertrain > Engine > Trouble Codes

Result

Proceed to

DTCs are not output

A

DTC P062F44 is output

B
A

CHECK FOR INTERMITTENT PROBLEMS

B

REPLACE ECM

    READ NEXT:

     VIN Not Programmed (P063051)

    MONITOR DESCRIPTION DTC P063051 is stored when the Vehicle Identification Number (VIN) or frame number is not stored in the ECM or the stored VIN or frame number is not accurate. DTC No. Detec

     Fuel Pump Control Module Internal Electronic Failure (P064A49)

    MONITOR DESCRIPTION The fuel pump control ECU has a self-diagnosis function. If there is an internal malfunction, the fuel pump control ECU sends a malfunction signal to the ECM via the FPC drive circ

     Actuator Supply Voltage "A" Circuit Short to Ground or Open (P065714)

    DESCRIPTION The electronic throttle control system has a dedicated power supply circuit. The voltage (+BM) is monitored and when it is low (less than 4 V), the ECM determines that there is a malfuncti

    SEE MORE:

     Inspection

    INSPECTION PROCEDURE 1. INSPECT OIL PRESSURE CONTROL VALVE ASSEMBLY (a) Measure the resistance according to the value(s) in the table below. Standard Resistance: Tester Connection Condition Specified Condition 1 - 2 20°C (68°F) 6.2 to 8.2 Ω If the res

     Software Incompatibility with Body Control Module Not Programmed (U032251,U032257)

    DESCRIPTION This DTC is stored when the destination information of the main body ECU (multiplex network body ECU) does not match that of the blind spot monitor sensors. DTC No. Detection Item DTC Detection Condition Trouble Area U032

    © 2020-2025 Copyright www.tcorollacross.com PT NL