Toyota Corolla Cross Owners & Service Manuals

Toyota Corolla Cross: Hybrid/EV Battery Energy Control Module EEPROM Calibration / Parameter Memory Failure (P062F46)

Toyota Corolla Cross (2022-2024) Service Manual / Engine & Hybrid System / Hybrid / Battery Control / Hybrid Battery System / Hybrid/EV Battery Energy Control Module EEPROM Calibration / Parameter Memory Failure (P062F46)

DESCRIPTION

The battery ECU assembly monitors its internal operation and will store these DTCs when it detects an internal malfunction. If these DTCs are output, replace the battery ECU assembly.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Warning Indicate

Note

P062F46

Hybrid/EV Battery Energy Control Module EEPROM Calibration / Parameter Memory Failure

ECU internal malfunction

(EEPROM error)

(1 trip detection logic)

Battery ECU assembly

Comes on

Master Warning:

Comes on

SAE Code: P062F

MONITOR DESCRIPTION

The battery ECU assembly monitors its internal operation. If the internal operation is malfunctioning, the battery ECU assembly illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Related DTCs

P062F (INF P062F46): Internal control module EEPROM (battery energy control module)

Required sensors/components

Battery ECU assembly

Frequency of operation

Continuous

Duration

TMC's intellectual property

MIL operation

1 driving cycle

Sequence of operation

None

TYPICAL ENABLING CONDITIONS

The monitor will run whenever the following DTCs are not stored

TMC's intellectual property

Other conditions belong to TMC's intellectual property

-

TYPICAL MALFUNCTION THRESHOLDS

TMC's intellectual property

-

COMPONENT OPERATING RANGE

Battery ECU assembly

DTC P062F (INF P062F46) is not detected

CONFIRMATION DRIVING PATTERN

HINT:

  • After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

    Click here

  • When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.

    Click here

  1. Connect the GTS to the DLC3.
  2. Turn the ignition switch to ON and turn the GTS on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for 2 minutes or more.
  5. Turn the ignition switch to ON and turn the GTS on.
  6. With ignition switch ON and wait for 2 minutes or more.[*1]

    HINT:

    [*1]: Normal judgment procedure.

    The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

  7. Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.
  8. Check the DTC judgment result.

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE, perform the normal judgment procedure again.

CAUTION / NOTICE / HINT

NOTICE:

Be sure to check that the applicable DTC is output from the hybrid battery system.

PROCEDURE

1.

CHECK DTC OUTPUT (HEALTH CHECK)

(a) Enter the following menus: System Select / Health Check.

(b) Check for DTCs.

Result

Proceed to

P062F46 is output from the hybrid battery system.

A

P062F46 is output from any system other than the hybrid battery system.

B

(c) Turn the ignition switch off.

A

REPLACE BATTERY ECU ASSEMBLY

B

GO TO PERFORM DIAGNOSIS FOR RESPECTIVE SYSTEM

    READ NEXT:

     Hybrid/EV Powertrain Control Module Unexpected Operation (P0A1D94)

    DESCRIPTION The battery ECU assembly monitors the hybrid vehicle control ECU via CAN communication. If the battery ECU assembly detects that the hybrid vehicle control ECU is malfunctioning, it will i

     Hybrid/EV Battery Cooling Fan 1 Control Circuit High (P0A8100,P0A8115)

    DESCRIPTION Refer to the description for DTC P0A8111. Click here DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Note P0A8

     Hybrid/EV Battery Cooling Fan 1 Component Internal Failure (P0A8196,P0A8198)

    DESCRIPTION Refer to the description for DTC P0A8111. Click here DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Note P0A8

    SEE MORE:

     Inspection

    INSPECTION PROCEDURE 1. INSPECT EGR VALVE ASSEMBLY (a) Measure the resistance according to the value(s) in the table below. Standard Resistance: Tester Connection Condition Specified Condition 1 (EGA+) - 2 (EGA-) 20°C (68°F) 3.1 to 3.7 Ω 3

     Installation

    INSTALLATION CAUTION / NOTICE / HINT COMPONENTS (INSTALLATION) Procedure Part Name Code 1 BRAKE ACTUATOR BRACKET CUSHION 44547B - - - 2 NO. 1 BRAKE

    © 2020-2024 Copyright www.tcorollacross.com