Toyota Corolla Cross Owners & Service Manuals

Toyota Corolla Cross: How To Proceed With Troubleshooting

CAUTION / NOTICE / HINT

HINT:

  • Use the following procedure to troubleshoot the blind spot monitor system.
  • *: Use the GTS.

PROCEDURE

1.

VEHICLE BROUGHT TO WORKSHOP

NEXT

2.

CUSTOMER PROBLEM ANALYSIS

HINT:

If there are any scratches or impact marks on the rear bumper, perform the blind spot monitor beam axis confirmation. If any abnormalities are found, perform the blind spot monitor sensor installation condition inspection.

NEXT

3.

INSPECT AUXILIARY BATTERY VOLTAGE

(a) Measure the auxiliary battery voltage with the ignition switch off.

Standard voltage:

11 to 14 V

If the voltage is below 11 V, replace or recharge the auxiliary battery before proceeding to the next step.

NEXT

4.

CHECK CAN COMMUNICATION SYSTEM*

(a) Use the GTS to check if the CAN communication system is functioning normally.

  • for HEV Model:

    Click here

  • for Gasoline Model:

    Click here

Result

Proceed to

CAN communication system DTCs are not output.

A

CAN communication system DTCs are output.

B

B

GO TO CAN COMMUNICATION SYSTEM

  • for HEV Model:

    Click here

  • for Gasoline Model:

    Click here

A

5.

CHECK FOR DTC AND FREEZE FRAME DATA*

(a) Check for DTCs.

Body Electrical > Blind Spot Monitor "B" > Trouble Codes Body Electrical > Blind Spot Monitor "A" > Trouble Codes

(b) Recheck for DTCs.

Body Electrical > Blind Spot Monitor "B" > Trouble Codes Body Electrical > Blind Spot Monitor "A" > Trouble Codes

(c) Record or print DTCs and freeze frame data, if necessary.

Result

Proceed to

DTCs are not output.

A

DTCs are output.

B

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

A

6.

CHECK VEHICLE CONTROL HISTORY (RoB)*

(a) Check for Vehicle control history (RoB) and note any codes that are output.

Body Electrical > Blind Spot Monitor "B" > Utility

Tester Display

Vehicle Control History (RoB)

Body Electrical > Blind Spot Monitor "A" > Utility

Tester Display

Vehicle Control History (RoB)

Result

Proceed to

Vehicle control history (RoB) is not output

A

Vehicle control history (RoB) is output

B

B

GO TO VEHICLE CONTROL HISTORY (RoB)

A

7.

PROBLEM SYMPTOMS TABLE

(a) Refer to Problem Symptoms Table.

Click here

Result

Proceed to

Fault is not listed in Problem Symptoms Table.

A

Fault is listed in Problem Symptoms Table.

B

HINT:

If the symptom does not recur and no DTCs are output, attempt to reproduce the symptoms.

Click here

B

GO TO PROBLEM SYMPTOMS TABLE

A

8.

PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM*

(a) Refer to Terminals of ECU.

Click here

(b) Refer to Diagnosis System.

Click here

(c) Refer to Data List / Active Test.

Click here

NEXT

9.

ADJUST, REPAIR OR REPLACE

Result

Proceed to

When adjusting or repairing

A

When replacing

B

B

GO TO STEP 11

A

10.

CLEAR DTC

(a) Clear the DTCs.

Body Electrical > Blind Spot Monitor "B" > Clear DTCs Body Electrical > Blind Spot Monitor "A" > Clear DTCs
NEXT

GO TO STEP 11

11.

PERFORM BEAM AXIS CONFIRMATION*

(a) Confirm the blind spot monitor beam axis display and perform the blind spot monitor beam axis adjustment.

Click here

NEXT

12.

PERFORM CONFIRMATION TEST

NEXT

END

    READ NEXT:

     Customize Parameters

    CUSTOMIZE PARAMETERS CUSTOMIZE BLIND SPOT MONITOR SYSTEM (a) Customizing with the GTS NOTICE: When the customer requests a change in a function, first make sure that the function can be cus

     Problem Symptoms Table

    PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed i

     Terminals Of Ecu

    TERMINALS OF ECU BLIND SPOT MONITOR SENSOR LH (B) Terminal No. (Symbol) Terminal Description Condition Specified Condition S12-4 (OM

    SEE MORE:

     Operation Check

    OPERATION CHECK CHECK WINDOW DEFOGGER SYSTEM NOTICE: If the auxiliary battery voltage becomes low, auxiliary battery load control will operate in order to ensure sufficient power is supplied to the power steering system. In this case, the window defogger system may not operate. HINT: The window de

     Back Door Closer General Electrical Failure (B225001)

    DESCRIPTION The multiplex network door ECU receives signals from the latch switch, initial switch, pawl switch and back door courtesy switch, which are built into the back door lock assembly. Based on these switch signals, the latch position of the back door lock with courtesy light switch assembly

    © 2020-2024 Copyright www.tcorollacross.com