Toyota Corolla Cross Owners & Service Manuals

Toyota Corolla Cross: Generator Position Sensor Circuit Voltage Below Threshold (P0A4B16,P0A4B1F)

Toyota Corolla Cross (2022-2024) Service Manual / Engine & Hybrid System / Hybrid / Battery Control / Motor Generator Control System / Generator Position Sensor Circuit Voltage Below Threshold (P0A4B16,P0A4B1F)

DTC SUMMARY

MALFUNCTION DESCRIPTION

These DTCs indicate that the resolver output signal is abnormal. The cause of this malfunction may be one of the following:

Area

Main Malfunction Description

Inverter low-voltage circuit

The connectors are not connected properly

Hybrid vehicle transaxle assembly

  • Short circuit in the generator resolver circuit
  • Generator (MG1) internal malfunction (entry of foreign matter, etc.)

Wire harness between the resolver and inverter with converter assembly

  • Short circuit in the wire harness
  • The connectors are not connected properly (entry of foreign matter or water, etc.)

Inside of inverter

Inverter with converter assembly internal circuit malfunction

DESCRIPTION

Refer to the system description for the Generator Resolver Circuit.

Click here

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Warning Indicate

Note

P0A4B16

Generator Position Sensor Circuit Voltage Below Threshold

Interphase short in the generator resolver circuit:

A short circuit between signal lines of generator resolver phases is electrically detected.

(1 trip detection logic)

  • Inverter with converter assembly
  • Hybrid vehicle transaxle assembly
  • Wire harness or connector

Comes on

Master Warning:

Comes on

SAE Code:

P0A4B

P0A4B1F

Generator Position Sensor Circuit Intermittent

A short circuit between signal lines of generator resolver phases is electrically detected when DTC P0C7917, P0E5717, P0D3319, P1C5D19, P1C5F19 or P1C5E19 is stored.

(1 trip detection logic)

  • Inverter with converter assembly
  • Hybrid vehicle transaxle assembly
  • Wire harness or connector

Does not come on

Master Warning:

Does not come on

SAE Code:

P0A4F

MONITOR DESCRIPTION

The motor generator control ECU monitors the Generator resolver output signal. If the motor generator control ECU detects output signals that are out of the normal range or specification, it will conclude that there is a malfunction in the generator resolver, illuminate the MIL and store a DTC.

MONITOR STRATEGY

Related DTCs

P0A4B (INF P0A4B16): Short circuit between phases

Required sensors/components

Generator resolver

Frequency of operation

Continuous

Duration

TMC's intellectual property

MIL operation

1 driving cycle

Sequence of operation

None

TYPICAL ENABLING CONDITIONS

The monitor will run whenever the following DTCs are not stored

TMC's intellectual property

Other conditions belong to TMC's intellectual property

-

TYPICAL MALFUNCTION THRESHOLDS

TMC's intellectual property

-

COMPONENT OPERATING RANGE

Motor generator control ECU

DTC P0A4B (INF P0A4B16) is not detected

CONFIRMATION DRIVING PATTERN

HINT:

  • After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

    Click here

  • When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.

    Click here

  1. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  2. Turn the ignition switch off and wait for 2 minutes or more.
  3. Turn the ignition switch to ON and wait for 5 seconds or more. [*1]
  4. Turn the ignition switch to ON (READY) with the shift lever in P and wait for 5 seconds or more. [*2]
  5. Depress the accelerator pedal of the vehicle with the engine stopped and the shift lever in P to start the engine. [*3]
  6. Drive the vehicle forward with the shift lever in D for 5 m (16 ft.) or more. [*4]
  7. Drive the vehicle backward with the shift lever in R for 5 m (16 ft.) or more. [*5]

    HINT:

    [*1] to [*5]: Normal judgment procedure.

    The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

  8. Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.
  9. Check the DTC judgment result.

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE, perform the normal judgment procedure again.

WIRING DIAGRAM

Refer to the wiring diagram for the Generator Resolver Circuit.

Click here

CAUTION / NOTICE / HINT

CAUTION:

Refer to the precautions before inspecting high voltage circuit.

Click here

NOTICE:

  • After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

    Click here

  • When disconnecting and reconnecting the auxiliary battery.

    HINT:

    When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

    Click here

HINT:

  • If the problem symptom cannot be reproduced, performing a road test on a road on which the vehicle tends to vibrate will make it easier to reproduce the symptom.
  • If the resolver is malfunctioning, the vehicle may not drive smoothly.
  • When inspecting the connectors, if it is difficult to judge if a connector was disconnected, deformed or improperly secured, disconnect and reconnect the connector and then check for DTCs again. Check if the same DTC is output. If the same DTC is not output, improper connection of connectors is suspected.
  • As a malfunction detection threshold may be exceeded when performing the vibration or heat connector inspections, make sure to perform the following inspection to check that the DTC was not stored due to the malfunction of a part.
  • P0A4B16 or P0A4B1F may be output as a result of the malfunctions indicated by the DTCs in table below.
    1. The chart above is listed in inspection order of priority.
    2. Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)
Table 1

Malfunction Content

System

Relevant DTC

Insulation malfunction

Hybrid control system

P1C7C49

Hybrid/EV Battery Voltage System Isolation (A/C Area) Internal Electronic Failure

P1C7D49

Hybrid/EV Battery Voltage System Isolation (Hybrid/EV Battery Area) Internal Electronic Failure

P1C7E49

Hybrid/EV Battery Voltage System Isolation (Transaxle Area) Internal Electronic Failure

P1C7F49

Hybrid/EV Battery Voltage System Isolation (Direct Current Area) Internal Electronic Failure

P1C8049

Hybrid/EV Battery Voltage System Isolation (Rear Motor Area) Internal Electronic Failure

Table 2

Malfunction Content

System

Relevant DTC

Microcomputer malfunction

Motor generator control system

P0A1A47

Generator Control Module Watchdog / Safety MC Failure

P0A1A49

Generator Control Module Internal Electronic Failure

P1C2A1C

Generator A/D Converter Circuit Circuit Voltage Out of Range

P1C2A49

Generator A/D Converter Circuit Internal Electronic Failure

P1C2A71

Generator A/D Converter Circuit Actuator Stuck

P313483

Communication Error from Drive Motor "A" to Generator Value of Signal Protection Calculation Incorrect

P313486

Communication Error from Drive Motor "A" to Generator Signal Invalid

P313487

Communication Error from Drive Motor "A" to Generator Missing Message

Power source circuit malfunction

Motor generator control system

P19F81C

Generator Control Module Offset Power Circuit Voltage Out of Range

P26DF1C

Generator Control Module Position Sensor REF Power Source Circuit Voltage Out of Range

PROCEDURE

1.

CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

Click here

Result

Proceed to

OK

A

NG (The connector is not connected securely.)

B

NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.)

C

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

A

2.

CHECK GENERATOR RESOLVER CIRCUIT

Click here

HINT:

If the "Generator Resolver Circuit" inspection results are normal, perform the next step.

NEXT

REPLACE INVERTER WITH CONVERTER ASSEMBLY

    READ NEXT:

     Generator Position Sensor Signal Amplitude < (P0A4B21,P0A1A47,P0A4B22,P1C2A49)

    DTC SUMMARY MALFUNCTION DESCRIPTION These DTCs indicate that the resolver output signal is abnormal. The cause of this malfunction may be one of the following: Area Main Malfunction Descripti

     Drive Motor "A" Phase V Current(High Resolution) Circuit Short to Battery (P0A6012,...,P0A631F)

    DESCRIPTION The motor generator control ECU (MG ECU), which is built into the inverter with converter assembly, monitors its internal operation and will store DTCs if it detects a malfunction.

     Drive Motor "B" Phase V Current(High Resolution) Circuit Short to Battery (P0A6912,...,P0A6C1F)

    DESCRIPTION The motor generator control ECU (MG ECU), which is built into the inverter with converter assembly, monitors its internal operation and will store DTCs if it detects a malfunction.

    SEE MORE:

     Parts Location

    PARTS LOCATION ILLUSTRATION *1 CANISTER *2 FUEL PUMP (for Low Pressure Side) *3 MASS AIR FLOW METER SUB-ASSEMBLY *4 PARK / NEUTRAL POSITION SWITCH ASSEMBLY *5 NO. 1 ENGINE ROOM RELAY BLOCK ASSEMBLY *6 NO. 2 RELAY BLOCK ASSEMBLY *7 FUE

     Problem Symptoms Table

    PROBLEM SYMPTOMS TABLE HINT: Depending on the multi-display settings, the background will remain started even when the ignition switch is turned off. For that reason, check the multi-display setting before performing an inspection. Click here General Function Symptom

    © 2020-2024 Copyright www.tcorollacross.com