Toyota Corolla Cross Owners & Service Manuals

Toyota Corolla Cross: Dtc Check / Clear

DTC CHECK / CLEAR

DTC CHECK

(a) Turn the ignition switch off.

(b) Connect the GTS to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn the GTS on.

(e) Read the DTCs following the prompts on the GTS.

Chassis > Brake/EPB > Trouble Codes

(f) Check the details of the DTCs.

NOTICE:

  • Make sure to clear the DTCs after repair.
  • The electronically controlled brake system outputs DTCs for the following system. When DTCs other than those in Diagnostic Trouble Code Chart for the electronically controlled brake system are output, refer to Diagnostic Trouble Code Chart for the relevant system.

    System

    Proceed to

    Electric Parking Brake System (for Gasoline Model)

Display Item

Description

Test Failed

Shows the malfunction judgment results during the current trip.

Confirmed

Shows the DTCs confirmed up to now (The number of current trips differs for each DTC.)

  • Freeze frame data is stored for each of the latest result DTCs and confirmed DTCs.
  • Refer to the diagnostic trouble code chart and perform the necessary troubleshooting procedures.

    Click here

(g) Check the freeze frame data.

(1) If a DTC is stored, check the corresponding freeze frame data to gain an understanding of the vehicle condition at the time.

Click here

CHECK TIME STAMP

HINT:

By checking Time Stamp, the time and order in which DTCs were stored in an ECU can be checked.

(a) Turn the ignition switch off.

(b) Connect the GTS to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn the GTS on.

(e) Enter the following menus: Health Check.

(f) Perform the following steps when the data setting screen is displayed.

(g) Select the systems for which to perform Health Check and check for time stamp data.

Selectable items:
  • Powertrain
  • Chassis
  • Body
  • Store All Data

(h) Select "Yes" when "Would you like to include Time Stamp Data?" is displayed.

HINT:

If "Yes" is not selected, time stamp data will not be stored.

(i) After Health Check has completed, select "Time Stamp Data" to display the Time Stamp screen.

(j) Select the desired system from the drop-down list on the bottom of the Time Stamp screen.

(k) Check the order and time which DTCs were stored for the selected system.

DTC CLEAR

(a) Turn the ignition switch off.

(b) Connect the GTS to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn the GTS on.

(e) Operate the GTS to clear the codes.

Chassis > Brake/EPB > Clear DTCs

(f) Press the DTC clear button.

NOTICE:

When DTCs are cleared, all data related to the DTCs is also cleared.

HINT:

If the malfunction continues, the DTCs will be stored again when the detection conditions are met.

    READ NEXT:

     Freeze Frame Data

    FREEZE FRAME DATA FREEZE FRAME DATA/INFORMATION (a) Using the GTS, check the vehicle condition (ECU, sensor) when the brake system operates or a DTC is output. CHECK FREEZE FRAME DATA AND INFORMA

     Fail-safe Chart

    FAIL-SAFE CHART FAIL-SAFE CHART (a) When the skid control ECU (brake actuator assembly) detects a solenoid valve malfunction or abnormal signal from a sensor, the brake actuator assembly cuts po

     Data List / Active Test

    DATA LIST / ACTIVE TEST DATA LIST (ELECTRONICALLY CONTROLLED BRAKE SYSTEM) NOTICE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend sol

    SEE MORE:

     Lack of Power

    DESCRIPTION Problem Symptom Suspected Area Trouble Area Engine speed fluctuation due to abnormal combustion Idle speed too low or high Strong engine vibration due to above symptoms Ignition malfunction Deviation in air fuel ratio (Excessive or i

     Reassembly

    REASSEMBLY CAUTION / NOTICE / HINT COMPONENTS (REASSEMBLY) Procedure Part Name Code 1 FRONT SIDE MARKER LIGHT BULB 81710F - - - 2 FRONT SIDE MARKER LIGHT SOCKET - - - - 3 FRONT TURN SIGNAL LIGHT BULB 81510D -

    © 2020-2024 Copyright www.tcorollacross.com