Toyota Corolla Cross Owners & Service Manuals

Toyota Corolla Cross: Right Rear Wheel ABS Hold Solenoid Control Circuit Short to Battery (C12E712,...,C12F249)

Toyota Corolla Cross (2022-2025) Service Manual / Brake / Brake Control / Dynamic Control Systems / Electronically Controlled Brake System (for Hev Model) / Right Rear Wheel ABS Hold Solenoid Control Circuit Short to Battery (C12E712,...,C12F249)

DESCRIPTION

The ABS solenoid relay and solenoid valves are built into the brake actuator assembly.

The rear solenoid valve RH controls the brake fluid pressure of the rear wheel cylinder RH of the vehicle.

When this DTC is stored, the fail-safe function operates and the ABS solenoid relay is turned off to prevent the solenoid valves from operating.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

DTC Output from

Note

C12E712

Right Rear Wheel ABS Hold Solenoid Control Circuit Short to Battery

A short to +B in the solenoid circuit is detected during the self-test.

Skid control ECU (brake actuator assembly)

Comes on

Brake/EPB
  • SAE Code: C12EA
  • Output ECU: Skid control ECU (brake actuator assembly)

C12E714

Right Rear Wheel ABS Hold Solenoid Control Circuit Short to Ground or Open

An open or short in the solenoid circuit is detected during the self-test.

Skid control ECU (brake actuator assembly)

Comes on

Brake/EPB
  • SAE Code: C12E9
  • Output ECU: Skid control ECU (brake actuator assembly)

C12E71C

Right Rear Wheel ABS Hold Solenoid Control Circuit Voltage Out of Range
  • A current leak in the solenoid circuit is detected during the self-test.
  • The solenoid operation request signal and solenoid operation feedback signal do not match for a certain period of time.

Skid control ECU (brake actuator assembly)

Comes on

Brake/EPB
  • SAE Code: C12E8 (Case 1 to 4)
  • Output ECU: Skid control ECU (brake actuator assembly)

C12E71E

Right Rear Wheel ABS Hold Solenoid Control Circuit Resistance Out of Range

An abnormal resistance in the solenoid circuit is detected during the self-test.

Skid control ECU (brake actuator assembly)

Comes on

Brake/EPB
  • SAE Code: C12E8 (Case 5)
  • Output ECU: Skid control ECU (brake actuator assembly)

C12E749

Right Rear Wheel ABS Hold Solenoid Control Internal Electronic Failure

An internal malfunction in the solenoid circuit is detected during the self-test.

Skid control ECU (brake actuator assembly)

Comes on

Brake/EPB
  • SAE Code: C12E7
  • Output ECU: Skid control ECU (brake actuator assembly)

C12F212

Right Rear Wheel ABS Release Solenoid Control Circuit Short to Battery

A short to +B in the solenoid circuit is detected during the self-test.

Skid control ECU (brake actuator assembly)

Comes on

Brake/EPB
  • SAE Code: C12F5
  • Output ECU: Skid control ECU (brake actuator assembly)

C12F214

Right Rear Wheel ABS Release Solenoid Control Circuit Short to Ground or Open

An open or short in the solenoid circuit is detected during the self-test.

Skid control ECU (brake actuator assembly)

Comes on

Brake/EPB
  • SAE Code: C12F4
  • Output ECU: Skid control ECU (brake actuator assembly)

C12F21C

Right Rear Wheel ABS Release Solenoid Control Circuit Voltage Out of Range
  • A current leak in the solenoid circuit is detected during the self-test.
  • The solenoid operation request signal and solenoid operation feedback signal do not match for a certain period of time.

Skid control ECU (brake actuator assembly)

Comes on

Brake/EPB
  • SAE Code: C12F3 (Case 1 to 4)
  • Output ECU: Skid control ECU (brake actuator assembly)

C12F21E

Right Rear Wheel ABS Release Solenoid Control Circuit Resistance Out of Range

An abnormal resistance in the solenoid circuit is detected during the self-test.

Skid control ECU (brake actuator assembly)

Comes on

Brake/EPB
  • SAE Code: C12F3 (Case 5)
  • Output ECU: Skid control ECU (brake actuator assembly)

C12F249

Right Rear Wheel ABS Release Solenoid Control Internal Electronic Failure

An internal malfunction in the solenoid circuit is detected during the self-test.

Skid control ECU (brake actuator assembly)

Comes on

Brake/EPB
  • SAE Code: C12F2
  • Output ECU: Skid control ECU (brake actuator assembly)

MONITOR DESCRIPTION

C12E7 and C12F2:
  • When the ABS solenoid is not operating and it is detected by the self-diagnosis function that there is an internal malfunction in the ABS solenoid circuit, the skid control ECU (brake actuator assembly) illuminates the MIL and stores this DTC.
C12E8 (Case 1) and C12F3 (Case 1):
  • When it is detected by the self-diagnosis function that the feedback value from the ABS solenoid drive circuit does not match the operation request value, the skid control ECU (brake actuator assembly) illuminates the MIL and stores this DTC.
C12E8 (Case 2) and C12F3 (Case 2):
  • When the downstream voltage of the ABS solenoid or the current flowing in the ABS solenoid is less than a certain value, the skid control ECU (brake actuator assembly) illuminates the MIL and stores this DTC.
C12E8 (Case 3) and C12F3 (Case 3):
  • When the ABS solenoid is not operating and the current flowing in the ABS solenoid exceeds a certain value (current leak is detected), the skid control ECU (brake actuator assembly) illuminates the MIL and stores this DTC.
C12E8 (Case 4) and C12F3 (Case 4):
  • If the current flowing in the ABS solenoid circuit, circuit temperature, or voltage drop within the circuit is a certain value or more, the skid control ECU (brake actuator assembly) judges that there is an ABS solenoid overcurrent malfunction and illuminates the MIL and stores this DTC.
C12E8 (Case 5) and C12F3 (Case 5):
  • If the ABS solenoid is not operating and the resistance value of the ABS solenoid is outside of a certain range, the skid control ECU (brake actuator assembly) illuminates the MIL and stores this DTC.
C12E9 and C12F4:
  • If the current in the ABS solenoid circuit, voltage or temperature is less than or exceeds a certain value, or the operation request value and feedback value deviate by a certain value or more, the skid control ECU (brake actuator assembly) illuminates the MIL and stores this DTC.
C12EA and C12F5:
  • When it is detected by the self-diagnosis function that there is a short to +B in the ABS solenoid circuit, the skid control ECU (brake actuator assembly) illuminates the MIL and stores this DTC.

MONITOR STRATEGY

Related DTCs

C12E7: Cyclic valve test for SRRH (built in self-test)

C12E8 (Case 1): Valve feedback monitoring for SRRH (PWM check)

C12E8 (Case 2): Valve feedback monitoring for SRRH (valve-coil path interruption)

C12E8 (Case 3): Cyclic valve test (current leakage test) for SRRH

C12E8 (Case 4): Valve feedback monitoring for SRRH (general application specific integrated circuit valve driver failure)

C12E8 (Case 5): Cyclic valve test (valve resistance check) for SRRH

C12E9: Cyclic valve test (silent valve driver test) for SRRH

C12EA: Cyclic valve test (valve actuation register test) for SRRH

C12F2: Cyclic valve test for SRRR (built in self-test)

C12F3 (Case 1): Valve feedback monitoring for SRRR (PWM check)

C12F3 (Case 2): Valve feedback monitoring for SRRR (valve-coil path interruption)

C12F3 (Case 3): Cyclic valve test (current leakage test) for SRRR

C12F3 (Case 4): Valve feedback monitoring for SRRR (general application specific integrated circuit valve driver failure)

C12F3 (Case 5): Cyclic valve test (valve resistance check) for SRRR

C12F4: Cyclic valve test (silent valve driver test) for SRRR

C12F5: Cyclic valve test (valve actuation register test) for SRRR

Required Sensors/Components(Main)

Skid control ECU (brake actuator assembly)

Required Sensors/Components(Related)

Skid control ECU (brake actuator assembly)

Frequency of Operation

During initial checking

Duration

-: C12E7, C12E8 (Case 3 and 5), C12E9, C12EA, C12F3 (Case 3 and 5), C12F4 and C12F5

0.03 seconds: C12E8 (Case 1, 2 and 4), C12F3 (Case 1, 2 and 4)

20 seconds: C12F2

MIL Operation

Immediately

Sequence of Operation

None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever the following DTCs are not stored

TMC's intellectual property

Other conditions belong to TMC's intellectual property

-

TYPICAL MALFUNCTION THRESHOLDS

TMC's intellectual property

-

COMPONENT OPERATING RANGE

TMC's intellectual property

-

CONFIRMATION DRIVING PATTERN

NOTICE:

When performing the normal judgment procedure, make sure that the driver door is closed and is not opened at any time during the procedure.

HINT:

  • After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
  • When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
  1. Connect the GTS to the DLC3.
  2. Turn the ignition switch to ON and turn the GTS on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off.
  5. Turn the ignition switch to ON (READY) and turn the GTS on.
  6. Wait for 1 second or more. [*]

    HINT:

    [*]: Normal judgment procedure.

    The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

  7. Enter the following menus: Chassis / Brake/EPB* / Utility / All Readiness.

    *: Electric Parking Brake System

  8. Check the DTC judgment result.

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE, perform driving pattern again.

PROCEDURE

1.

REPLACE BRAKE ACTUATOR ASSEMBLY

Click here

NEXT

END

    READ NEXT:

     Steering Angle Sensor / Yaw Rate Sensor / Lateral Acceleration Sensor Signal Correlation Failure (C135F00)

    DESCRIPTION The airbag ECU assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition. When the skid control ECU (brake actuator assembly) detects an abnormal acc

     Brake System Control Module "A" System Voltage System Voltage High (C137BA3)

    DESCRIPTION If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits ABS, brake assist, regene

     Stop Lamp Relay Actuator Stuck On (C13807E)

    DESCRIPTION When any of the following conditions are met, the skid control ECU (brake actuator assembly) sets the drive output (STPO) ON which operates the stop light control relay (stop light sw

    SEE MORE:

     Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor B (P001700)

    DESCRIPTION Refer to DTC P001313. Click here DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note P001700 Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor B Deviation in the crankshaft position sensor signal and camshaft posi

     Components

    COMPONENTS ILLUSTRATION *1 CENTER COWL TOP VENTILATOR LOUVER *2 BRAKE MASTER CYLINDER RESERVOIR FILLER CAP ASSEMBLY *3 HOOD TO COWL TOP SEAL - - ILLUSTRATION *1 FRONT

    © 2020-2025 Copyright www.tcorollacross.com