Toyota Corolla Cross: Lost Communication with Hybrid Powertrain Control Module (Hybrid/EV Battery Local Bus) Missing Message (U115087)
DESCRIPTION
The battery ECU assembly transmits and receives signals via CAN communication to and from the hybrid vehicle control ECU.
|
DTC No. | Detection Item |
DTC Detection Condition |
Trouble Area | MIL |
Warning Indicate | Note |
|---|---|---|---|---|---|---|
|
U115087 | Lost Communication with Hybrid Powertrain Control Module (Hybrid/EV Battery Local Bus) Missing Message |
The battery ECU assembly does not receive any signals from the hybrid vehicle control ECU for 1 second or more. (1 trip detection logic) |
CAN communication system |
Comes on | Master Warning: Comes on | SAE Code: U1150 |
MONITOR DESCRIPTION
If the battery ECU assembly cannot communicate with the hybrid vehicle control ECU via CAN communication, it will illuminate the MIL and store a DTC.
MONITOR STRATEGY
|
Related DTCs | U1150 (INF U115087): Lost communication with hybrid control module (battery bus) |
|
Required sensors/components | Battery ECU assembly |
|
Frequency of operation | Continuous |
|
Duration | TMC's intellectual property |
|
MIL operation | Immediately |
|
Sequence of operation | None |
TYPICAL ENABLING CONDITIONS
|
The monitor will run whenever the following DTCs are not stored |
TMC's intellectual property |
|
Other conditions belong to TMC's intellectual property |
- |
TYPICAL MALFUNCTION THRESHOLDS
|
TMC's intellectual property | - |
COMPONENT OPERATING RANGE
|
Battery ECU assembly | DTC U1150 (INF U115087) is not detected |
CONFIRMATION DRIVING PATTERN
HINT:
- After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
.gif)
- When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
- Connect the GTS to the DLC3.
- Turn the ignition switch to ON and turn the GTS on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the ignition switch off and wait for 2 minutes or more.
- Turn the ignition switch to ON and turn the GTS on.
- With ignition switch ON and wait for 2 minutes or more.[*1]
HINT:
[*1]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.
- Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE, perform the normal judgment procedure again.
PROCEDURE
|
1. | CHECK DTC OUTPUT (HV BATTERY) |
(a) Check for DTCs.
Powertrain > HV Battery > Trouble Codes(b) Turn the ignition switch off.
| NEXT | .gif) | GO TO CAN COMMUNICATION SYSTEM |
READ NEXT:
"HAVE TRACTION BATTERY INSPECTED" is displayed
DESCRIPTION The battery ECU assembly monitors the SOC (State Of Charge) of the HV battery. When it finds the HV battery has deteriorated excessively, it will display "Have Traction Battery Inspected"
ECU Power Source Circuit
DESCRIPTION If the ignition switch is ON, the battery ECU assembly applies current to the MREL terminal to turn the IGCT relay on. This supplies power to the IGCT terminals. WIRING DIAGRAM
CAUTION
SEE MORE:
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
HINT:
If a problem occurs in certain locations or at certain times of day, check for the possibility of wave interference.
When the electrical key transmitter sub-assembly is brought near an electrical key and tire pressure warning ECU and receiver (RF band), door o
Continuously variable transmission
Select the shift position
depending on your purpose
and situation.
Shift position purpose
and functions
P - Parking the vehicle/
starting the engine
R - Reversing
N - Neutral
(Condition in which the
power is not transmitted)
D - Normal driving*
M - 10-speed sport sequential
shiftmatic mode
driving
*
