Toyota Corolla Cross Owners & Service Manuals

Toyota Corolla Cross: Electronic Brake Booster Control Module "A" Signal Compare Failure (C121F62)

DESCRIPTION

When the self-check function of the electric brake booster (brake booster with master cylinder assembly) detects an internal circuit malfunction, this DTC is stored.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

DTC Output from

Note

C121F62

Electronic Brake Booster Control Module "A" Signal Compare Failure

Electric brake booster (brake booster with master cylinder assembly) internal malfunction detected.

Electric brake booster (brake booster with master cylinder assembly)

Comes on

Brake Booster

  • SAE Code: C121F (Case 1)
  • Output ECU: Electric brake booster (brake booster with master cylinder assembly)

MONITOR DESCRIPTION

When the electronically controlled brake system is starting and the non-volatile memory in the electric brake booster (brake booster with master cylinder assembly) is invalid or cannot be read, the electric brake booster (brake booster with master cylinder assembly) illuminates the MIL and stores this DTC.

MONITOR STRATEGY

Related DTCs

C121F (Case 1): EEPROM read error

Required Sensors/Components(Main)

Electric brake booster (brake booster with master cylinder assembly)

Required Sensors/Components(Related)

Electric brake booster (brake booster with master cylinder assembly)

Frequency of Operation

During initial checking

Duration

-

MIL Operation

Immediately

Sequence of Operation

None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever the following DTCs are not stored

TMC's intellectual property

Other conditions belong to TMC's intellectual property

-

TYPICAL MALFUNCTION THRESHOLDS

TMC's intellectual property

-

COMPONENT OPERATING RANGE

TMC's intellectual property

-

CONFIRMATION DRIVING PATTERN

NOTICE:

When performing the normal judgment procedure, make sure that the driver door is closed and is not opened at any time during the procedure.

HINT:

  • After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
  • When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
  1. Connect the GTS to the DLC3.
  2. Turn the ignition switch to ON and turn the GTS on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off.
  5. Turn the ignition switch to ON (READY) and turn the GTS on.
  6. Wait for 1 second or more. [*]

    HINT:

    [*]: Normal judgment procedure.

    The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

  7. Enter the following menus: Chassis / Brake Booster / Utility / All Readiness.
  8. Check the DTC judgment result.

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE, perform driving pattern again.

PROCEDURE

1.

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

Click here

NEXT

END

    READ NEXT:

     Electronic Brake Booster Control Module "A" Missing Message (C121F87,...,C14CC1C)

    DESCRIPTION The brake control power supply assembly is used as an auxiliary power supply for brake control when the voltage of the auxiliary battery is low. DTC No. Detection

     ECM Communication (C124A00)

    DESCRIPTION If the vehicle information stored by the skid control ECU (brake actuator assembly) does not match that sent from the ECM or a new skid control ECU (brake actuator assembly) is instal

     Electronic Brake Booster Control Module "A" Backup Power Supply Voltage System Voltage Low (C125DA2,C125DA3)

    DESCRIPTION The brake control power supply assembly is used as an auxiliary power supply for brake control when the voltage of the auxiliary battery is low. DTC No. Detection

    SEE MORE:

     Right Side Restraints Sensor 5 Signal Above Allowable Range (B009E85)

    DESCRIPTION DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode B009E85 Right Side Restraints Sensor 5 Signal Above Allowable Range Either condition is met: Side airbag pressure sensor RH malfunction

     Using the dynamic radar cruise control

    Setting the vehicle speed 1. Press the driving assist mode select switch to select dynamic radar cruise control. The dynamic radar cruise control indicator will illuminate. 2. Using the accelerator pedal, accelerate or decelerate to the desired vehicle speed (approximately 20 mph [30 km/h] or more

    © 2020-2024 Copyright www.tcorollacross.com