Toyota Corolla Cross: Electronic Brake Booster Motor "A" Power Supply Circuit "A" Internal Electronic Failure (C145D49,C145D71)
DESCRIPTION
The main relay is built into the electric brake booster (brake booster with master cylinder assembly).
When the electric brake booster (brake booster with master cylinder assembly) detects a malfunction in a circuit necessary for main relay to operate, or in the main relay itself, this DTC is stored.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
DTC Output from |
Note |
|---|---|---|---|---|---|---|
|
C145D49 |
Electronic Brake Booster Motor "A" Power Supply Circuit "A" Internal Electronic Failure |
Main relay inside electric brake booster (brake booster with master cylinder assembly) stuck ON detected. |
Electric brake booster (brake booster with master cylinder assembly) |
Comes on |
Brake Booster |
|
|
C145D71 |
Electronic Brake Booster Motor "A" Power Supply Circuit "A" Actuator Stuck |
Main relay inside electric brake booster (brake booster with master cylinder assembly) power source circuit condition detected. |
Electric brake booster (brake booster with master cylinder assembly) |
Comes on |
Brake Booster |
|
MONITOR DESCRIPTION
C145D (Case 1):- When the power supply voltage of the electric brake booster (brake booster with master cylinder assembly) is a certain value or more, the electronically controlled brake system is starting, and a main relay malfunction inside the electric brake booster (brake booster with master cylinder assembly) is detected, the electric brake booster (brake booster with master cylinder assembly) illuminates the MIL and stores this DTC.
- When a main relay malfunction inside the electric brake booster (brake booster with master cylinder assembly) is detected during the self-diagnosis that is performed during startup of the electronically controlled brake system, the electric brake booster (brake booster with master cylinder assembly) illuminates the MIL and stores this DTC.
MONITOR STRATEGY
|
Related DTCs |
C145D (Case 1): Booster master switch initial test C145D (Case 2): Booster master switch failsafe logic test |
|
Required Sensors/Components(Main) |
Electric brake booster (brake booster with master cylinder assembly) |
|
Required Sensors/Components(Related) |
Electric brake booster (brake booster with master cylinder assembly) |
|
Frequency of Operation |
During initial checking |
|
Duration |
0.015 seconds: C145D (Case 1) 1 second after ignition switch ON: C145D (Case 2) |
|
MIL Operation |
Immediately |
|
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
|
Monitor runs whenever the following DTCs are not stored |
TMC's intellectual property |
|
Other conditions belong to TMC's intellectual property |
- |
TYPICAL MALFUNCTION THRESHOLDS
|
TMC's intellectual property |
- |
COMPONENT OPERATING RANGE
|
TMC's intellectual property |
- |
CONFIRMATION DRIVING PATTERN
NOTICE:
When performing the normal judgment procedure, make sure that the driver door is closed and is not opened at any time during the procedure.
HINT:
- After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
- When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
- Connect the GTS to the DLC3.
- Turn the ignition switch to ON and turn the GTS on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the ignition switch off.
- Turn the ignition switch to ON (READY) and turn the GTS on.
- Wait for 1 second or more. [*]
HINT:
[*]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Enter the following menus: Chassis / Brake Booster / Utility / All Readiness.
- Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE, perform driving pattern again.
PROCEDURE
|
1. |
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY |
Click here .gif)
| NEXT | .gif)
|
END |
READ NEXT:
Electronic Brake Booster Motor "A" Temperature Sensor "A" Circuit Voltage Out
of Range (C148A1C,...,C149A1C)
DESCRIPTION
Refer to DTC C11704B
Click here
DTC No.
Detection Item
DTC Detection Condition
Trouble Area
MIL
DTC Output from
Multi-axis Acceleration Sensor Module "A" Supply Voltage Circuit Voltage Out
of Range (C14D71C)
DESCRIPTION
The airbag ECU assembly has a built-in yaw rate and acceleration
sensor and detects the vehicle condition.
This DTC is stored when the skid control ECU (brake actuator
assembly) rece
Left Front Wheel Speed Sensor Supply Voltage Circuit Short to Ground or Open
(C14E014)
DESCRIPTION
Refer to DTC C050012
Click here
DTC No.
Detection Item
DTC Detection Condition
Trouble Area
MIL
DTC Output from
SEE MORE:
Head restraints
Head restraints are provided
for all seats.
WARNING
■Head restraint precautions
Observe the following precautions
regarding the head restraints.
Failure to do so may result in
death or serious injury.
Use the head restraints
designed for each respective
seat.
Adjust the head restraints to th
Parts Location
PARTS LOCATION ILLUSTRATION
*A w/ Ambient Illumination Light
*B w/ Vanity Light
*1 FRONT DOOR AMBIENT ILLUMINATION LIGHT LH (FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH)
*2 FRONT DOOR AMBIENT ILLUMINATION LIGHT RH (FRONT DOOR TRIM BOARD SUB-ASSEMBLY RH)
*3 M
