Toyota Corolla Cross Owners & Service Manuals

Toyota Corolla Cross: System Voltage (AM) Circuit Voltage Below Threshold (P1AFC00)

DESCRIPTION

The battery ECU assembly monitors its internal operation and will store these DTCs when it detects an internal malfunction.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Warning Indicate

Note

P1AFC00

System Voltage (AM) Circuit Voltage Below Threshold

The battery ECU assembly shutdown memory procedure did not complete normally in consecutive 40 trips.

(1 trip detection logic)

  • Wire harness or connector
  • Battery ECU assembly
  • Fuse

Does not come on

Master Warning:

Comes on

SAE Code: P1AFC

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click here

  1. Connect the GTS to the DLC3.
  2. Turn the ignition switch to ON and turn the GTS on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for 2 minutes or more.
  5. Turn the ignition switch to ON and wait for 11 seconds or more. *1
  6. Turn the ignition switch off and wait for 2 minutes or more. *2
  7. Perform the procedures *1 and *2 41 times or more.
  8. Turn the ignition switch to ON and turn the GTS on.
  9. Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.
  10. Check the DTC judgment result.

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE, perform driving pattern again.

WIRING DIAGRAM

Refer to the wiring diagram for DTC P056014.

Click here

CAUTION / NOTICE / HINT

CAUTION:

Refer to the precautions before inspecting high voltage circuit.

Click here

NOTICE:

  • After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

    Click here

  • When disconnecting and reconnecting the auxiliary battery

    HINT:

    When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

    Click here

PROCEDURE

1.

CHECK FUSE (ECU-B NO. 2)

Click here

NG

REPLACE FUSE (ECU-B NO. 2)

OK

2.

CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY)

Click here

NG

CONNECT SECURELY

OK

3.

CHECK HARNESS AND CONNECTOR (AM VOLTAGE)

Click here

OK

REPLACE BATTERY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY ECU ASSEMBLY POWER SOURCE CIRCUIT)

    READ NEXT:

     Flying Capacitor Circuit Voltage Out of Range (P1AFD00)

    DESCRIPTION The battery ECU assembly monitors its internal operation and will store these DTCs when it detects an internal malfunction. DTC No. Detection Item DTC Detection Condition

     Hybrid/EV Battery ECU Multiple Reset (P1AFF00)

    DESCRIPTION The battery ECU assembly monitors its internal operation and will store these DTCs when it detects an internal malfunction. DTC No. Detection Item DTC Detection Condition

     Hybrid/EV Battery Current Sensor for Driving Control Circuit Short to Ground (P1C9F11,P1C9F15)

    DESCRIPTION Refer to the description for DTC P0ABF11. Click here DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Note P1C9

    SEE MORE:

     Brake System Control Module "A" System Voltage Line Internal Electronic Failure (C117A49,C137BA2)

    DESCRIPTION If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits ABS, brake assist, regenerative braking, etc. operation. This DTC is stored when the +BS terminal voltage meets one of the

     Front Passenger Side Electrical Antenna Circuit Open (B27A213)

    DESCRIPTION The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the front door outside handle assembly RH (electrical key antenna) at intervals of 0.25 seconds. For the front door outside handle assembly RH (electrical key antenna) to detect when the

    © 2020-2024 Copyright www.tcorollacross.com